Installation
LR1-KIT Installation Guide
Getting Started Unpacking Carefully remove all items from the shipping box and inspect. Make sure there are no broken parts or missing items. If you received multiple units, they may be labels that identify each unit according to information shared ...
Rhōmb 2 Door Access Kit Installation Guide
Getting Started Unpacking Carefully remove all items from the shipping box and inspect. Make sure there are no broken parts or anything missing (see next page for box contents). If you received multiple units, they may be labels that identify each ...
Configuring ENS Cameras for Eagle Eye Networks
Overview From the factory, ENS cameras cannot be discovered by video management systems like Eagle Eye and OpenEye. The cameras must be initialized and then configured before shipping to the client in order to ensure compatibility with their system ...
Brivo SDC Installation Guide
Getting Started Unpacking Carefully remove all items from the shipping box and inspect. Make sure there are no broken parts or anything missing (see next page for box contents). If you received multiple units, they may be labels that identify each ...
ACS-300 Wiring from PDK Single io Door Controller
Overview This article outlines the wiring diagram for access control systems currently using the PDK Single io Door Controller being moved to the Brivo ACS-300. Please note that each installation differs slightly. Verify your connections, the labels ...
Wiring for Brivo & Farpointe OSDP Readers
Overview Instead of using the READER 1/2 ports on the ACS-300, OSDP readers use the port labeled RS-485, located next to the READER 1 port. In the diagram, this is located in the top-right of the controller. However, your configuration may vary, so ...
Brivo Single Door Controller (SDC) Maglock Wiring Diagram
Brivo SDC Maglock Wiring Diagram
Installing a Brivo Cellular Module
Overview The Brivo cellular module is a great way to deliver Internet where the service doesn't exist. It is more reliable than wi-fi and not dependent on any wiring. The following guide provides installation instructions for control panels provided ...
Taking Door Measurements
Door Measurements are vital when ordering the correct lock hardware. The following is a guide for taking measurements. We also list the most common measurements for each one so you know you're doing it right! 1. Door Width: Measure from edge to edge ...
Barcode Reader Programming - C900 Optical
Overivew The C900 optical barcode reader can be programmed one of two ways. Facility Code "0" Mode - this is for barcodes with 5* digits or less and whose value falls within the Wiegand card id range (1 - 65535). *Note: this will work with 6-digit ...
Run Network Diagnostics on Eagle Eye Devices Through SSH
Overview This guide covers connection to the Eagle Eye device through SSH and Eagle Eye's built-in Network Diagnostics tool. This is suitable for intermediate to ad Identify the Device's Local IP Address Before the device can be accessed through SSH, ...
Brivo Access Cam Installation
Access Control Cabling & Door Preparation
Overview The following is a guide on preparing doors for cabling and access control hardware. This guide provides specifications based on the door and lock type. This guide serves as recommended guidelines for new construction, where walls are ...
Barcode Reader Installation - M350 Optical
Overivew The following guide provides details for mounting and wiring the M350 Optical barcode reader. What's in the Box 1-gang junction box w/mounting screws Custom 3D printed adapter w/mounting screws Reader mounting ring w/mounting screws Barcode ...
LS2-4A-AQL Installation Guide
Getting Started Unpacking Carefully remove all items from the shipping box and inspect. Make sure there are no broken parts or anything missing (see next page for box contents). If you received multiple units, they may be labels that identify each ...
ACS-300 Board Connections (without integrated power supply)
Overview This article shows the basic layout of the connection points for the ACS-300 by Brivo. For a thorough guide on the full installation of our LS2-3A-ALX units, an install guide is located here. ...
Switching from ID-Tech Barcode Swipe to Optical Barcode Reader
Overview Due to electrical differences and manufacturing decisions, some steps need to be taken when switching from an ID-Tech Barcode reader to an Optical Barcode reader. This article goes over the process of properly switching the voltages as well ...
Installing Varistors into Latitude Control Panels
Overview Sometimes electric strikes and other locks will send pulses back to the control panel when locking and unlocking, which results in errors within Brivo's event log. Installing varistors into the control panel's power input and the lock relay ...
LS2-3A-ALX Installation Guide
Getting Started Unpacking Carefully remove all items from the shipping box and inspect. Make sure there are no broken parts or anything missing (see next page for box contents). If you received multiple units, they may be labels that identify each ...
Schlage AD-400 Battery Change
The batteries should be changed annually at a minimum, but they may require changing up to every six months if there is heavy usage or if the signal strength is low. Installing or replacing batteries Approximately one month prior to the end of the ...
Replacing a Wiegand Card/PIN Reader
Here's a brief video with step-by-step instructions for swapping an old reader with a new reader.
2N Intercom Relay Integration
Amazon KfB Provisioning
Step 1: Download the KfB App (Andriod only) Step 2: Login Username: lssjwpie Password: Amazon2! Step 3: Start Job a) Click on Job Name from the project list b) Click Start Job button Step 4: Assign Gateway a) Scan the QR code provided by ...
Amazon KfB Installation
Installing a Wiegand Reader
Overview The following instructions guide you through how to connect a Wiegand reader to the Brivo OnAir control panel and mounting the reader. IMPORTANT - Always power OFF the control panel before making any connections. Cable Requirements # ...
Programming Output Mode of Farpointe PIN Pad Reader
Overview The Farpointe P-620/640 readers have two output modes, 8-bit Burst and 26-bit Wiegand. The default mode is 8-bit Burst, which works with access control systems that manage PIN codes separate from Card IDs, such as Brivo OnAir. If Card IDs, ...
AD-400 Unpacking Hardware
NDE Wireless Cylindrical Lock
AD-400 Cylindrical Lock Rehanding
AD-400 Cylindrical Lock Door Preparation
AD-400 Electrical Connections
AD-400 Cylindrical Lock Installation